Mazda 3 manuals

Mazda 3 Service Manual: Engine SST [Skyactiv G 2.0]

Mazda 3 Service Manual / Engine / General / Engine SST [Skyactiv G 2.0]

1: Mazda SST number

2: Global SST number

Example


1:49 UN20 5072

2:205–072

Holder




1: –

2: 134-01049A

Evaporative emission system tester


1:–

2:AKS042808

Adapter


1: 49 UN20 5072

2: 205–072

Holder


1: 49 B011 105

2: –

Adapter


1: 49 E033 101

2: –

Dust cover installer


1: 49 UN30 3050

2: 303–050

Engine lifting bracket


1: 49 C017 5A0

2: –

Engine support set


1: 49 L017 5A0

2: –

Support hanger


1: 49 G028 205

2: –

Oil seal installer


1: 49 G014 001

2: –

Oil filter wrench


1: 49 B015 001

2: –

Adapter

(Part of 49 B015 0A0)


1: 49 B015 002

2: –

Adapter

(Part of 49 B015 0A0)


1: 49 0187 280A

2: –

Oil pressure gauge


1: 49 D019 908

2: –

Gauge

(Part of 49 D019 9A2)


1: 49 D019 909

2: –

Hose

(Part of 49 D019 9A2)


1: 49 D019 910

2: –

Adapter

(Part of 49 D019 9A2)


1: 49 D019 911

2: –

Adapter

(Part of 49 D019 9A2)


1: 49 N013 103A

2: –

Remover

(Part of 49 N013 1A0D)


1: 49 E042 001

2: –

Remover


1: 49 N013 1A0D

2: –

Fuel pressure gauge set


1: 49 D013 1A0

2: –

Injector seal installer set


1:49 D015 001

2:–

Box wrench


1:49 L018 001

2:–

O2 sensor wrench


—


Engine SST [Mzr 2.3 Disi Turbo]
1: Mazda SST number 2: Global SST number Example 1:49 UN30 3328 2:303–328 Rear oil seal replacer 1:– 2:303–507 Crankshaft TDC t ...

Engine Tune Up [Mzr 2.0, Mzr 2.5]
NOTE: If the accelerator pedal is depressed continuously for a specified time, the engine speed may decrease to the idle speed. This is due to the fuel cut control operation, which preve ...

Other materials:

LDA (Lane Departure Alert)
Basic functions In the Subaru Solterra, the Lane Departure Alert (LDA) system is designed to assist the driver by monitoring the vehicle’s position relative to lane markings or road boundaries*. When the system detects a potential deviation, it provides timely warnings and can also apply ge ...

Power Brake Unit Removal/Installation [Mzr 2.3 Disi Turbo]
CAUTION: Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again. Therefore, replace the switch with a new one when replacing the power brake unit or performing any procedure that changes the pedal stroke. Secure the steering wheel using tap ...

General Procedures (Front And Rear Axles)
Wheel and Tire Installation 1. When installing the wheels and tires, tighten the wheel nuts in a criss-cross pattern to the following tightening torque. Tightening torque 88—118 N·m {9.0—12 kgf·m, 65—87 ft·lbf} Connector Disconnection 1. Disconnect the negative batte ...

� 2016-2026 Copyright www.mazda3tech.com