Mazda 3 Service Manual: Steering
- General Procedures (Steering)
- Precaution
- Steering SST
- Steering Switch Inspection
- Steering Switch Removal/Installation
- Linkage, Power
- Air Bleeding
- Electric Power Steering Oil Pump Component Disassembly/Assembly
- Electric Power Steering Oil Pump Component Removal/Installation
- Electro Hydraulic Power Assist Steering (EHPAS) Control Module Configuration
- Electro Hydraulic Power Assist Steering (EHPAS) Control Module Inspection
- Oil Control Valve (OCV) Inspection [Mzr 2.0, Mzr 2.5]
- Oil Control Valve (OCV) Inspection [Mzr 2.3 Disi Turbo]
- Oil Control Valve (OCV) Inspection [Skyactiv G 2.0]
- Oil Control Valve (OCV) Removal/Installation [Mzr 2.0, Mzr 2.5]
- Oil Control Valve (OCV) Removal/Installation [Mzr 2.3 Disi Turbo]
- Oil Control Valve (OCV) Removal/Installation [Skyactiv G 2.0]
- Power Steering Fluid Inspection
- Power Steering Fluid Line Component Removal/Installation
- Steering Shaft Inspection
- Steering Gear And Linkage Assembly
- Steering Gear And Linkage Disassembly
- Steering Gear And Linkage Inspection
- Steering Gear And Linkage Removal/Installation
- Wheel, Column
- Steering Shaft Inspection
- Steering Wheel And Column Inspection
- Steering Wheel And Column Removal/Installation [With Advanced Keyless Entry And Push Button Start System]
- Steering Wheel And Column Removal/Installation [Without Advanced Keyless Entry And Push Button Start System]
- Combination Switch Disassembly/Assembly
- Combination Switch Removal/Installation
- No.6 Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
Seat Belt Inspection
Belt
1. Verify that the belt is installed properly with no twists or kinks.
2. Verify that there is no damage to the seat belt and no deformation of the
metal fittings.
If there is any ...
General Procedures (Steering)
Wheel and Tire Installation
1. When installing the wheels and tires, tighten the wheel nuts in a criss-cross
pattern to the following tightening torque.
Tightening torque
88—118 N· ...
Other materials:
Brake Fluid Pressure Sensor Inspection
1. Switch the ignition to off.
2. Install the SSTs to the master cylinder (secondary side) as shown in
the figure.
NOTE:
When installing the SST (49 D043 0A0) to the master cylinder, use
a commercially available flare nut wrench (flare nut across flat 12 mm {0.47
in}).
...
Brake Pedal Inspection
Pedal Height Inspection
1. Measure the distance from the center of the upper surface of the pedal pad
to the floor covering and verify that it is as specified.
If not within the specification, replace the brake pedal.
Brake pedal height (reference value)
MZR 2.0, SKYACTI ...
Rear Shock Absorber Disposal
1. Clamp a rear shock absorber on a flat surface or with the piston pointing
downwards.
2. Drill a 2—3 mm {0.08—0.11 in} hole at a point 40—50 mm {1.6—1.9
in} from the bottom of the tube, so that the gas can escape.
WARNING:
Whenever drilling into a rear shock absorber, w ...
