Mazda 3 Service Manual: Information
- Accelerator Pedal Removal/Installation [Mzr 2.0, Mzr 2.5]
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment Control System]
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Two Step Deployment Control System]
- Barometric Pressure (Baro) Sensor Inspection [Mzr 2.0, Mzr 2.5]
- Clock Spring Inspection [Standard Deployment Control System]
- Clock Spring Inspection [Two Step Deployment Control System]
- Control System Personalization Features Setting Procedure
- Driver Side Air Bag Module Removal/Installation [Standard Deployment Control System]
- Driver Side Air Bag Module Removal/Installation [Two Step Deployment Control System]
- Front Seat Belt Removal/Installation [Standard Deployment Control System]
- Front Seat Belt Removal/Installation [Two Step Deployment Control System]
- Ion Sensor Inspection [Skyactiv G 2.0]
- Neutral Switch Inspection [Mzr 2.0, Mzr 2.5]
- PCM Configuration [Mzr 2.0, Mzr 2.5]
- PCM Inspection [Mzr 2.0, Mzr 2.5]
- PCM Removal/Installation [Mzr 2.0, Mzr 2.5]
- PID/Data Monitor Inspection [Standard Deployment Control System]
- PID/Data Monitor Inspection [Two Step Deployment Control System]
- Passenger Side Air Bag Module Removal/Installation [Standard Deployment Control System]
- Passenger Side Air Bag Module Removal/Installation [Two Step Deployment Control System]
- Pressure Sensor Removal/Installation [Two Step Deployment Control System]
- Restraints SST [Standard Deployment Control System]
- Restraints SST [Two Step Deployment Control System]
- Seat Track Position Sensor Removal/Installation [Two Step Deployment Control System]
- Seat Weight Sensor Calibration [Two Step Deployment Control System]
- Seat Weight Sensor Control Module Removal/Installation [Two Step Deployment Control System]
- Seat Weight Sensor Inspection [Two Step Deployment Control System]
- Seat Weight Sensor Removal/Installation [Two Step Deployment Control System]
- Side Air Bag Sensor No. 1 Removal/Installation [Two Step Deployment Control System]
- Side Air Bag Sensor No. 2 Removal/Installation [Two Step Deployment Control System]
- Side Air Bag Sensor Removal/Installation [Standard Deployment Control System]
- Throttle Body Inspection [Mzr 2.0, Mzr 2.5]
- Throttle Position (TP) Sensor Inspection [Mzr 2.0, Mzr 2.5]
- Variable Tumble Shutter Valve Switch Inspection [Mzr 2.0, Mzr 2.5]
- Variable Swirl Shutter Valve Switch Inspection [Mzr 2.3 Disi Turbo]
Control
...
Accelerator Pedal Removal/Installation [Mzr 2.0, Mzr 2.5]
1. Remove the battery cover..
2. Disconnect the negative battery cable..
3. Remove the driver-side lower panel..
4. Remove in the order indicated in the table.
1
AP ...
Other materials:
Rear Turn Light Bulb Removal/Installation
4SD
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Trunk mat.
b. Trunk board.
c. Trunk end trim.
3. Partially peel back the trunk side trim..
4. Remove in the order indicated in the table.
1
Connector
2
...
Power Metal Oxide Semiconductor Field Effect Transistor (Power Mos Fet) Inspection
[Full Auto Air Conditioner]
1. Verify that the continuity between the power MOS FET terminals is as indicated
in the table.
If there is any malfunction, replace the power MOS FET.
If the blower motor operation is not normal even though no malfunction can
be verified, inspect the climate control unit..
...
Spark Plug Inspection [Skyactiv G 2.0]
Specification
Spark plug type
PE01-18110, PE02-18110, PE5R-18110, PE5S-18110
Plug Gap Inspection
CAUTION:
To avoid possible damage to the tip, do not adjust the plug gap.
To prevent damaging the tip, use a wire type plug gap gauge when inspecting
the plug gap.
...
