Mazda 3 Service Manual: Accessories
- Cruise Control
- Cruise Control Switch Inspection [Mzr 2.0, Mzr 2.5]
- Cruise Control Switch Inspection [Mzr 2.3 Disi Turbo]
- Electronics
- Power Sockets
- Safety Systems
- Active Command Modes Inspection [Blind Spot Monitoring (Bsm)]
- Blind Spot Monitoring (Bsm) Bracket Removal/Installation
- Blind Spot Monitoring (Bsm) Control Module Inspection
- Blind Spot Monitoring (Bsm) Control Module Removal/Installation
- Blind Spot Monitoring (Bsm) Indicator Light Inspection
- Blind Spot Monitoring (Bsm) Indicator Light Removal/Installation
- Blind Spot Monitoring (Bsm) Off Switch Inspection
- Blind Spot Monitoring (Bsm) Off Switch Removal/Installation
- No.6 Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- PID/Data Monitor Inspection [Blind Spot Monitoring (Bsm)]
- Security & Keyless Entry
- Forced Ignition On [With Advanced Keyless Entry And Push Button Start System]
- Relay Block Inspection [With Advanced Keyless Entry And Push Button Start System]
- Relay Block Removal/Installation [With Advanced Keyless Entry And Push Button Start System]
- Steering Wheel And Column Removal/Installation [With Advanced Keyless Entry And Push Button Start System]
- Steering Wheel And Column Removal/Installation [With Advanced Keyless Entry And Push Button Start System]
- Steering Wheel And Column Removal/Installation [Without Advanced Keyless Entry And Push Button Start System]
- Theft Deterrent System Clearing Freeze Frame Data
- Theft Deterrent System Reading Freeze Frame Data
- Door Lock Switch Inspection
- Door Lock Switch Removal/Installation
- Keyless Antenna Removal/Installation
- Keyless Beeper Inspection
- Keyless Beeper Removal/Installation
- Keyless Control Module Configuration
- Keyless Control Module Inspection
- Keyless Control Module Removal/Installation
- Front Door Key Cylinder Removal/Installation
- Front Door Key Cylinder Switch Inspection
- Trunk Lid Key Cylinder Removal/Installation
- Ignition Switch Inspection [Without Advanced Keyless Entry And Push Button Start System]
- Ignition Switch Removal/Installation [Without Advanced Keyless Entry And Push Button Start System]
- Storage
- Blind Spot Monitoring (Bsm) Indicator Light Inspection
- Blind Spot Monitoring (Bsm) Indicator Light Removal/Installation
- No.6 Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- Passenger Air Bag Deactivation (Pad) Indicator Light Bulb Removal/Installation [Two Step Deployment Control System]
- Trailer
Cruise Control
...
Other materials:
No.1 Car Navigation System Does Not Start Operation [Car Navigation System]
1
Even if the NAVI mode is selected, the car-navigation system screen does
not display.
Possible DTC
—
POSSIBLE CAUSE
NAVI button malfunction
Power supply fuse (+B, ACC) burnt out ...
Joint Shaft Assembly [Mzr 2.3 Disi Turbo]
1. Assemble in the order indicated in the table.
1
Bracket
2
Dust seal (RH)
.
3
Bearing
.
4
Dust seal (LH)
.
5
Joint shaft
.
Dust Seal ...
Filament Repair
1. Clean the filament using isopropyl alcohol.
2. Attach tape to both sides of the filament.
3. Using a small brush or marking pen, apply silver paint.
4. After 2—3 min, carefully remove the tape without damaging the applied
area.
CAUTION:
Do not operate the rear window defro ...
