Mazda 3 Service Manual: Brakes
- General
- Brake Fluid Air Bleeding
- Brake Fluid Inspection
- Brake Fluid Pressure Sensor Inspection
- Brake Hose (Front) Removal/Installation [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
- Brake Hose (Front) Removal/Installation [Mzr 2.3 Disi Turbo]
- Brake Hose (Rear) Removal/Installation [Mzr 2.0, Skyactiv G 2.0]
- Brake Hose (Rear) Removal/Installation [Mzr 2.5, Mzr 2.3 Disi Turbo]
- Brake Pedal Inspection
- Brake Pedal Removal/Installation
- Brake/Taillight Bulb Removal/Installation
- Brakes SST
- Disc Pad (Front) Replacement [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
- Disc Pad (Front) Replacement [Mzr 2.3 Disi Turbo]
- Disc Pad (Rear) Replacement
- General Procedures (Brake)
- Master Cylinder Removal/Installation [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
- Master Cylinder Removal/Installation [Mzr 2.3 Disi Turbo]
- Power Brake Unit Inspection
- Power Brake Unit Removal/Installation [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
- Power Brake Unit Removal/Installation [Mzr 2.3 Disi Turbo]
- Vacuum Hose Removal/Installation [Mzr 2.0, Mzr 2.5]
- Vacuum Hose Removal/Installation [Mzr 2.3 Disi Turbo]
- Vacuum Hose Removal/Installation [Skyactiv G 2.0]
- Vacuum Line Inspection
- Vacuum Pump Inspection [Skyactiv G 2.0]
- Vacuum Pump Removal/Installation [Skyactiv G 2.0]
- Brake Control, Vehicle Dynamics
- DSC HU/CM Inspection
- DSC HU/CM Removal/Installation
- DSC Off Switch Inspection
- DSC Off Switch Removal/Installation
- DSC Sensor Initialization Procedure
- Precaution [Dynamic Stability Control (DSC)]
- ABS
- Sensors, Switches, Relays
- Disc Brakes
- Caliper (Front) Disassembly/Assembly [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
- Caliper (Front) Disassembly/Assembly [Mzr 2.3 Disi Turbo]
- Caliper (Rear) Disassembly/Assembly
- Front Brake (Disc) Inspection
- Front Brake (Disc) Removal/Installation [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
- Front Brake (Disc) Removal/Installation [Mzr 2.3 Disi Turbo]
- Rear Brake (Disc) Inspection
- Rear Brake (Disc) Removal/Installation
- Parking Brake
- Parking Brake Cable Removal/Installation
- Parking Brake Lever Adjustment
- Parking Brake Lever Inspection
- Parking Brake Lever Removal/Installation
- Parking Brake Switch Inspection
- Sensors, Switches, Relays
Rain Sensor Removal/Installation
1. Disconnect the negative battery cable..
2. Spread open the rain sensor cover in the direction of the arrows and disengage
tabs A to remove it.
3. Disconnect the rain sensor connector.
...
General
...
Other materials:
Heater, Ventilation And Air Conditioning
Abbreviation
A/C
Air Conditioning
Features
The full-auto air conditioner has been adopted for vehicles with SKYACTIV-G
2.0.
Specifications
Full-auto air conditioner
Basic system
Item
Specification
...
Brake Fluid Pressure Sensor Inspection
1. Switch the ignition to off.
2. Install the SSTs to the master cylinder (secondary side) as shown in
the figure.
NOTE:
When installing the SST (49 D043 0A0) to the master cylinder, use
a commercially available flare nut wrench (flare nut across flat 12 mm {0.47
in}).
...
Front Door Glass Removal/Installation
1. To access the glass installation bolt, position the front door glass so that
the distance from the top of the front door glass to the upper part of the front
beltline molding is approx. 80 mm {3.1 in}.
2. Disconnect the negative battery cable..
3. Remove the inner garnish..
4. Remov ...
